bing tracking image

Best Honda Fit Tow Bars

change vehicle


Tow Bar Videos

Best 2017 Honda Fit Flat Tow Set Up - Braking System

Ryan: Hey everybody, Ryan here at etrailer. Today we're going to be talking about your best flat tow setup for your 2017 Honda Fit. There's going to be five main components needed to flat tow your Honda Fit. You're going to have the baseplate, which the baseplate's going to provide us with a solid connection point. That way, we can hook our tow bar up to it. That tow bar is going to be the second thing that we're going to need.



Best 2016 Honda Fit Flat Tow Set Up - Braking System

Hey everybody, Ryan here at etrailer. Today we're going to be talking about your best flat tow setup for your 2016 Honda Fit. There's going to be five main components needed to flat tow your Honda Fit. You're going to have the baseplate, which the baseplate's going to provide us with a solid connection point. That way, we can hook our tow bar up to it. That tow bar is going to be the second thing that we're going to need.



Roadmaster Tow Bar Installation - 2012 Honda Fit

Today on our 2012 Honda Fit, well be doing a test fit with our Roadmaster Falcon 2 tow bar, which is rated at 6000 pounds, part #RM-520. To start our test fit, you will need to install the tow bar into the receiver of your tow vehicle. To attach the tow bar to the towed vehicle, you will need to remove the pin on either side of the base plate. You will extend the arms of the tow bar out, lining it up on the bracket of the towed vehicle. Then you will reinstall the pin and the clevis pin that goes through it. You will repeat this for both sides.



RoadMaster Falcon Tow Bar Installation - 2011 Honda Fit

Today, on our 2011 Honda Fit, were going to be installing the RoadMaster Falcon All Terrain Toolbar. Part number RM-522. This vehicle has already had the base plate and a previous tow bar installed on it, so were actually just replacing with this new Falcon All Terrain Tow Bar. Were going to need to attach these brackets to the removable arms. We want to make sure that we have the drivers side and that this side points up. Now well take the plate, comes with the kit.Take a hex bolt, go through the plate, the bracket and through the removable arm.



Roadmaster Base Plate Installation - 2011 Honda Fit

Alright, today on this 2011 Honda Fit we are going to install part number 521190-1 from Roadmaster. This is their EZ base plate kit. What we have done so far is removed the front wheels. You do not really have to do that but sometimes it makes it a little bit easier to get to stuff to help remove the front clip when you are ready to take it off. Now we will go ahead and start by removing some of the top plastic fasteners that are underneath the hood. We are removing these five fasteners here. The best way is to just pull out the center. Then pop it up. Now there is a fastener right here that we need to remove. There will be one on each side to do. We are done with the driver side. We will do the same thing on the passenger side. Alright, there are a variety of fasteners we need to remove underneath. It is the same thing as the fasteners on top. Just pop out the middle and just pull them out. Since these are on the bottom, it will probably take a little bit more force. 1:15



Base Plate Wiring Harness Installation - 2010 Honda Fit

Today on this 2010 Honda Fit we are going to install a diode isolating kit part number 38955. The first thing we need to do to get started is that when we take our wire harness we are going to tape up part of this and then we will do the whole length and periodically apply some tape to keep everything under control. We will let our ground loop hang out and continue on. What we are going to do is take our 4-pole first and we are going to route it down towards the grill and we are going to pull it out by our base plates. Just leave it like that for now. 00:39



Roadmaster Base Plate Installation - 2010 Honda Fit

Today on this 2010 Honda Fit we are going to install a Roadmaster EZ Base Plate kit part number 521190-1 from Roadmaster. The first thing we need to do is take off the front bumper cover itself. It requires removing a bunch of fasteners on top of the grill, and a bunch of fasteners at the very bottom of the fascia underneath the vehicle. We will do the leading one on the edge right here. We will start popping them out with a screw driver first and use a rivet tool to pull out the rest, and work our way around. :33





Honda Fit Tow Bar Questions